Congratulations on your purchase of the Fenix L2D. The Fenix L2D is a high-tech, rugged tool that's perfect for any lighting application. It features six settings, 4 of them being output levels. This flexibility not only allows the user to select the best compromise between brightness and runtime for any given task but also has ability to aid in an emergency. The L2D does all this and still retains an incredibly compact size. If you're looking for solid reliability, digitally regulated brightness, and compact size, this Fenix is for you.

The Fenix L2D uses two AA batteries to drive its Premium Cree Q5 LED. The switch button is not only easy to operate with one hand, but it is recessed into the tail frame so the flashlight can stand up on its end, illuminating a room like a candle. The compact, lightweight, and precision-made flashlight comes with a lanyard as well as a belt case so you can carry it in your pocket or on your belt.

Features:

• Utilizes a Premium (Q5) Cree 7090 XR-E LED with a life of 50,000 hours
  
• Two modes of output, selected by turning the bezel (patented) - 6 Levels total
  
• General Mode: 12 lumens (55hrs) -> 53 lumens (10.5hrs) -> 107 lumens (4hrs) -> SOS
  
• Turbo Mode: 180 lumens (2.4hrs) -> Strobe
  
• Digitally Regulated for Constant Brightness
  
• Use two 1.5V AA ( Alkaline, Ni-MH, Lithium ) batteries , inexpensive and widely available
  
• 14.7cm (Length) x 2.1cm (Diameter)
  
• Made of aircraft grade aluminum
  
• Durable Type III hard anodized finish
  
• 56 gram weight (excluding batteries)
  
• Waterproof to IPX-8 Standard
  
• Toughened ultra clear glass lens with AR coating
  
• Push-button tail cap switch
  
• Input Voltage 1.0V - 4.2V
  
• Capable of standing up securely on a flat surface to serve as a candle
  
• Included Accessories
  

Operation

Fully press (click) to switch on and turn the bezel to select the General Mode or the Turbo Mode. A soft-press (no click) anytime while the light is on will change the brightness levels of a certain mode. Keep the light off for over 2 seconds and the light will turn completely off, restoring the regulation circuit to the default setting.

Usage and Maintenance

- Turbo Mode should be used sparingly. Due to its high power consumption, an excessive amount of heat may build up. Under high ambient temperatures, please do not use the Turbo Mode for more than 10 minutes continuously, doing so may harm the battery and the flashlight.

- Please do not disassemble the sealed part in the head of the flashlight; doing so will void the warrantee. It will also damage the flashlight or hamper the flashlight’s function.

- Please use quality 1.5 volts AA batteries so as not to lead to the damage of the flashlight due to leaks and other self-destructive behavior.

- Please take your battery out of the flashlight if you will not use the light for a long time or the power of the battery has run out. Otherwise, some poor battery’s leaks may damage the light.

- Please put the battery's Positive (+) side towards the light's head. Reverse polarity may damage the circuit.

- Please replace the o-rings if they are damaged after using for a long time and regularly lubricant the o-rings as to not erode the rubber. Doing so will keep the flashlight properly sealed against water.

- Please clean the contacts of your light from time to time, especially if the light flickers or doesn’t light up. There may be several reasons for a flickering or not working light:

Reason A: The battery needs replacing.

Solution: Replace batteries (Please confirm the correct installation of anode and cathode).

Reason B: The threads, PCB board contact or other contacts are dirty.

Solution: Clean the contact points with an alcohol soaked cotton swab.

Reason C: The head, tube or internal parts of the tail cap are loose.

Solution: add some lubricant on the 0-ring and screw the head and tail in (including inside parts of the tail) tightly.

If the above methods don’t work, please contact the distributors and refer to the warranty policy.

Product Warranty

We will replace products afflicted with manufacturing defects within 15 days of purchase and repair a light free of charge within 12 months of purchase if problems develop with normal use; if repair is required after 12 months from the date of purchase, we will charge for parts. The total repair fee is dictated by the cost of the replaced materials.