The Fenix L2T V2.0 takes the simple yet effective interface of the LxT series and upgrades the light with a more efficient emitter for a brighter, more intense beam. Also new is a textured reflector, eliminating artifacts and dark spots some smooth reflectors can create. The L2T V2.0 still retains the ability to select between high and low beam with a simple twist of the head, allowing the user to select the best compromise between brightness and runtime. Unlike traditional flashlights which dim considerably as the batteries wears down, a fully regulated circuit enables the Fenix L2T V2.0 to maintain near maximum brightness as its battery's voltage decreases. L2T V2.0 compromises nothing and is still built tough to last.

The Fenix L2T v2 uses two AA batteries to drive its CREE Q2 LED. The compact, lightweight, and precision-made flashlight comes with a lanyard as well as a belt case so you can carry it in your pocket or on your belt.

Features:

• Utilizes a Cree Q2 X-Lamp LED with a life of 50,000 hours
  
• Two levels of output, selected by turning the bezel (patented)
  
• High Output: Constant 152 Lumens, 2.4 hours (Ni-MH)
  
• Low Output: Constant 16 Lumens, 32 hours (Ni-MH)
  
• Uses two 1.5V AA ( Alkaline, Ni-MH, Lithium ) batteries, inexpensive and widely available
  
• 14.4cm (Length) x 2.1cm (Diameter)
  
• Made of aircraft grade aluminum
  
• Durable Type III hard anodized finish
  
• 60 gram weight (excluding batteries)
  
• Waterproof to IPX-8 Standard
  
• Toughened ultra clear glass lens with AR coating
  
• Push-button tail cap tactical switch - Forward Clickie - Tactical Switch
  
• Input Voltage 1.0V - 4.2V
  
• Textured Reflector for perfect beam
  
• Includes a holster, lanyard, two spare o-rings, and a rubber switch boot

Usage and Maintenance


- Please do not disassemble the sealed part in the head of the flashlight; doing so will void the warranty. It will also damage the flashlight or hamper the flashlight’s function.

- Please use quality 1.5 volts AA batteries so as not to lead to the damage of the flashlight due to leaks and other self-destructive behavior.

- Please take your battery out of the flashlight if you will not use the light for a long time or the power of the battery has run out. Otherwise, some poor battery’s leaks may damage the light.


- Please put the battery's Positive (+) side towards the light's head. Reverse polarity may damage the circuit.

- Please replace the o-rings if they are damaged after using for a long time and regularly lubricant the o-rings as to not erode the rubber. Doing so will keep the flashlight properly sealed against water.


- Please clean the contacts of your light from time to time, especially if the light flickers or doesn’t light up. There may be several reasons for a flickering or not working light:


Reason A: The battery needs replacing.

Solution: Replace batteries (Please confirm the correct installation of anode and cathode).


Reason B: The threads, PCB board contact or other contacts are dirty.

Solution: Clean the contact points with an alcohol soaked cotton swab.


Reason C: The head, tube or internal parts of the tail cap are loose.

Solution: add some lubricant on the 0-ring and screw the head and tail in (including inside parts of the tail) tightly.


If the above methods don’t work, please contact the distributors and refer to the warranty policy.

Product Warranty


We will replace products afflicted with manufacturing defects within 15 days of purchase and repair a light free of charge within 12 months of purchase if problems develop with normal use; if repair is required after 12 months from the date of purchase, we will charge for parts. The total repair fee is dictated by the cost of the replaced materials. Please contact Lighthound with any repair or warranty questions.